Home Power management LED drivers Illumination LED drivers

TPS92411

ACTIVE

Floating switch for offline AC linear direct drive of LEDs with Low Ripple current

Product details

Input voltage type AC Linear Topology AC Direct-Drive, Floating Switch Vin (min) (V) 8 Vin (max) (V) 94 Vout (max) (V) 94 Vout (min) (V) 9 Iout (max) (A) 0.35 Iq (typ) (mA) 0.2 Features Soft Switching Operating temperature range (°C) -40 to 150 Dimming method Forward Phase (Triac), Reverse Phase Number of channels 1 Rating Catalog
Input voltage type AC Linear Topology AC Direct-Drive, Floating Switch Vin (min) (V) 8 Vin (max) (V) 94 Vout (max) (V) 94 Vout (min) (V) 9 Iout (max) (A) 0.35 Iq (typ) (mA) 0.2 Features Soft Switching Operating temperature range (°C) -40 to 150 Dimming method Forward Phase (Triac), Reverse Phase Number of channels 1 Rating Catalog
HSOIC (DDA) 8 29.4 mm² 4.9 x 6 SOT-23 (DBV) 5 8.12 mm² 2.9 x 2.8
  • High-Performance Solution for Driving LEDs from AC Mains
  • Simplifies Design of Phase Dimmable LED Driver with High Power
    Factor, Low Total Harmonic Distortion, and Low Current Ripple
  • Suitable for LED Luminaires up to 70+ W
  • Input Voltage Range: 7.5 V to 100 V
  • Stackable 100 V, 2-Ω MOSFET Building Block
  • Controlled Switch Open and Close Transitions Minimize EMI
  • Designed for use with the TPS92410 or with a Discrete
    Linear Regulator
  • Input Undervoltage Protection
  • Output Overvoltage Protection (TPS92411P)
  • Low IQ: 200 µA (typ)
  • High-Performance Solution for Driving LEDs from AC Mains
  • Simplifies Design of Phase Dimmable LED Driver with High Power
    Factor, Low Total Harmonic Distortion, and Low Current Ripple
  • Suitable for LED Luminaires up to 70+ W
  • Input Voltage Range: 7.5 V to 100 V
  • Stackable 100 V, 2-Ω MOSFET Building Block
  • Controlled Switch Open and Close Transitions Minimize EMI
  • Designed for use with the TPS92410 or with a Discrete
    Linear Regulator
  • Input Undervoltage Protection
  • Output Overvoltage Protection (TPS92411P)
  • Low IQ: 200 µA (typ)

The TPS92411 is a 100-V floating MOSFET switch for use in offline LED lighting applications. The device is used in conjunction with a current regulator that can achieve a power factor greater than 0.9 to create a LED drive solution with low-ripple current. When properly designed, solution performance is comparable to traditional flyback, buck or boost-based AC/DC LED drivers. The approach requires no inductive components, thus saving size and cost. Slew-controlled low-frequency operation of the TPS92411 switches creates very little EMI. Detailed operation is described in the Application Information section.

Package options include SOT23-5 and PSOP-8 allowing the user to optimize for small size or scale for high power. Using the PSOP-8 package, design of LED luminaires up to 70 W or more is possible. Other features include a UVLO circuit to monitor when the device has sufficient voltage to operate properly and over-voltage protection (TPS92411P).

The TPS92411 is a 100-V floating MOSFET switch for use in offline LED lighting applications. The device is used in conjunction with a current regulator that can achieve a power factor greater than 0.9 to create a LED drive solution with low-ripple current. When properly designed, solution performance is comparable to traditional flyback, buck or boost-based AC/DC LED drivers. The approach requires no inductive components, thus saving size and cost. Slew-controlled low-frequency operation of the TPS92411 switches creates very little EMI. Detailed operation is described in the Application Information section.

Package options include SOT23-5 and PSOP-8 allowing the user to optimize for small size or scale for high power. Using the PSOP-8 package, design of LED luminaires up to 70 W or more is possible. Other features include a UVLO circuit to monitor when the device has sufficient voltage to operate properly and over-voltage protection (TPS92411P).

Download View video with transcript Video

Technical documentation

star =Top documentation for this product selected by TI
No results found. Please clear your search and try again.
View all 2
Type Title Date
* Data sheet TPS92411x Floating Switch for Offline AC Linear Direct Drive of LEDs with Low Ripple Current datasheet (Rev. B) PDF | HTML 28 Apr 2014
White paper Common LED Functions and LED Driver Design Considerations 21 Sep 2020

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Evaluation board

TPS92410EVM-001 — TPS92410EVM-001 Evaluation Module

The TPS92410VEVM-001 implements a 120V linear regulator dimming solution using theTPS92410 and TPS92411 integrated circuits from Texas Instruments. The TPS92410 is a linear controller with analog dimming functionality, thermal foldback, and a mode switch function to improve compatibility with phase (...)

User guide: PDF
Not available on TI.com
Evaluation board

TPS92410EVM-002 — TPS92410EVM-002 Evaluation Module

The TPS92410VEVM implements a 230V linear regulator dimming solution using the TPS92410 and TPS92411 integrated circuits from Texas Instruments. The TPS92410 is a linear controller with analog dimming functionality, thermal foldback, and a mode switch function to improve compatibility with phase (...)

User guide: PDF
Not available on TI.com
Evaluation board

TPS92411EVM-001 — TPS92411 Floating Switch evaluation board module for 120VAC Linear Direct Drive of LEDs

The TPS92411EVM-001 implements a 120VAC, 12W, phase dimmable light engine with high power factor and low LED current ripple on a single-sided metal core printed circuit board (MCPCB). The included LED drive circuit is comprised of a high voltage linear regulator and TPS92411 floating switches (...)

User guide: PDF
Not available on TI.com
Evaluation board

TPS92411EVM-002 — TPS92411 Floating Switch evaluation board module for 230VAC Linear Direct Drive of LEDs

The TPS92411EVM-002 implements a 230V linear regulator dimming solution using the TPS92411 integrated circuit from Texas Instruments. The TPS92411 is a smart switch designed to connect the LEDs in series at the proper times during a line cycle. The EVM can support applications up to ~16W.

User guide: PDF
Not available on TI.com
Simulation model

TPS92411 PSpice Transient Model (Rev. A)

SLUM410A.ZIP (108 KB) - PSpice Model
Simulation model

TPS92411 TINA-TI Transient Reference Design (Rev. A)

SLUM421A.TSC (163 KB) - TINA-TI Reference Design
Simulation model

TPS92411 TINA-TI Transient Spice Model (Rev. A)

SLUM422A.ZIP (16 KB) - TINA-TI Spice Model
Calculation tool

SLVC579 TPS92410 120V Calculator

Supported products & hardware

Supported products & hardware

Products
Illumination LED drivers
TPS92410 Switch-controlled, direct drive, linear controller for offline LED drivers TPS92411 Floating switch for offline AC linear direct drive of LEDs with Low Ripple current
Calculation tool

TPS92411-120VDESIGN-CALC TPS92411 120V Calculator

The TPS92411-120V Design Calculator is an Excel based design tool to aid in determining the external component values required to implement a 120VAC input LED drive solution using TPS92411, 100 V floating MOSFET switches. TPS92411's used in conjunction with a current regulator create an (...)

Supported products & hardware

Supported products & hardware

Products
Illumination LED drivers
TPS92411 Floating switch for offline AC linear direct drive of LEDs with Low Ripple current
Hardware development
Evaluation board
TPS92411EVM-001 TPS92411 Floating Switch evaluation board module for 120VAC Linear Direct Drive of LEDs
Calculation tool

TPS92411-230VDESIGN-CALC TPS92411 230V Calculator

The TPS92411-230V Design Calculator is an Excel based design tool to aid in determining the external component values required to implement a 230VAC input LED drive solution using TPS92411, 100 V floating MOSFET switches. TPS92411's used in conjunction with a current regulator create an (...)

Supported products & hardware

Supported products & hardware

Products
Illumination LED drivers
TPS92411 Floating switch for offline AC linear direct drive of LEDs with Low Ripple current
Hardware development
Evaluation board
TPS92411EVM-001 TPS92411 Floating Switch evaluation board module for 120VAC Linear Direct Drive of LEDs
Simulation tool

PSPICE-FOR-TI — PSpice® for TI design and simulation tool

PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Reference designs

TIDA-01399 — 50-W, 120-V AC Offline, LED Driver, No Magnetics, Reference Design for LED General Lighting

This reference design uses TPS92410 and TPS92411 with 50-W output power for area lighting with all components on a single printed-circuit board (PCB). This design uses four TPS92411 stages allowing 16 different switch states during the rising and falling rectified-AC waveform, which optimizes (...)
Design guide: PDF
Schematic: PDF
Reference designs

PMP6025 — 120VAC Input,3.5W Output LED Driver Candelabra (E12) & Small Form Factor LED Lig Reference Design

PMP6025 is a simple, magnetic-free, AC linear LED light engine design utilizing TPS92411 floating switches to deliver approximately 400 lumens when supplied with 120V mains AC.  The form factor has been optimized to fit standard E12 Candelabra Edison Screw (CES) light bulb bases.  EMI, (...)
Test report: PDF
Schematic: PDF
Reference designs

PMP6020 — 230 VAC In/17W Output LED Driver Using No Magnetic Components Reference Design

This 230VAC LED driver design (PMP6020) is form-factor optimized for use in recessed can fixtures, or downlights, and is dimmable using standard TRIAC wall dimmers.  It achieves low LED current ripple and >0.9 power factor without using inductors or transformers.
Test report: PDF
Schematic: PDF
Reference designs

PMP6022 — 120 VAC 7W PFC Wall Dimmable AC Linear Floating Switch LED Driver Reference Design

This magnetic-free (no transformer/inductor), small form-factor, LED driver circuit is ideal for use in LED lamps, downlights, and fixtures.  The design takes advantage of relatively new high forward-voltage (22V), low-current (20mA) white LEDs to realize a compact design producing >800 (...)
Test report: PDF
Schematic: PDF
Reference designs

PMP6021 — Fault Protected 230 VAC In/17W Output LED Driver Using No Magnetic Components Reference Design

This 230VAC LED driver design (PMP6021) is form-factor optimized for use in recessed can fixtures, or downlights, and is dimmable using standard TRIAC wall dimmers or via analog signal from an optional MCU.  It achieves low LED current ripple and >0.9 power factor without using (...)
Test report: PDF
Schematic: PDF
Package Pins Download
HSOIC (DDA) 8 View options
SOT-23 (DBV) 5 View options

Ordering & quality

Information included:
  • RoHS
  • REACH
  • Device marking
  • Lead finish/Ball material
  • MSL rating/Peak reflow
  • MTBF/FIT estimates
  • Material content
  • Qualification summary
  • Ongoing reliability monitoring
Information included:
  • Fab location
  • Assembly location

Recommended products may have parameters, evaluation modules or reference designs related to this TI product.

Support & training

TI E2E™ forums with technical support from TI engineers

Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.

If you have questions about quality, packaging or ordering TI products, see TI support. ​​​​​​​​​​​​​​

Videos